U.S. Code of Federal Regulations
Regulations most recently checked for updates: Feb 23, 2020
(a) Applicability. The rules in this section are applicable to the transportation of logs with the following exceptions:
(3) Firewood, stumps, log debris and other such short logs must be transported in a vehicle or container enclosed on both sides, front, and rear and of adequate strength to contain them. Longer logs may also be so loaded.
(b) Components of a securement system. (1) Logs must be transported on a vehicle designed and built, or adapted, for the transportation of logs. Any such vehicle must be fitted with bunks, bolsters, stakes or standards, or other equivalent means, that cradle the logs and prevent them from rolling.
(2) All vehicle components involved in securement of logs must be designed and built to withstand all anticipated operational forces without failure, accidental release or permanent deformation. Stakes or standards that are not permanently attached to the vehicle must be secured in a manner that prevents unintentional separation from the vehicle in transit.
(3) Tiedowns must be used in combination with the stabilization provided by bunks, stakes, and bolsters to secure the load unless the logs:
(i) are transported in a crib-type log trailer (as defined in 49 CFR 393.5), and
(ii) are loaded in compliance with paragraphs (b)(2) and (c) of this section.
(4) The aggregate working load limit for tiedowns used to secure a stack of logs on a frame vehicle, or a flatbed vehicle equipped with bunks, bolsters, or stakes must be at least one-sixth the weight of the stack of logs.
(c) Use of securement system. (1) Logs must be solidly packed, and the outer bottom logs must be in contact with and resting solidly against the bunks, bolsters, stakes or standards.
(2) Each outside log on the side of a stack of logs must touch at least two stakes, bunks, bolsters, or standards. If one end does not actually touch a stake, it must rest on other logs in a stable manner and must extend beyond the stake, bunk, bolster or standard.
(3) The center of the highest outside log on each side or end must be below the top of each stake, bunk or standard.
(4) Each log that is not held in place by contact with other logs or the stakes, bunks, or standards must be held in place by a tiedown. Additional tiedowns or securement devices must be used when the condition of the wood results in such low friction between logs that they are likely to slip upon each other.
(d) Securement of shortwood logs loaded crosswise on frame, rail and flatbed vehicles. In addition to the requirements of paragraphs (b) and (c) of this section, each stack of logs loaded crosswise must meet the following rules:
(1) In no case may the end of a log in the lower tier extend more than one-third of the log's total length beyond the nearest supporting structure on the vehicle.
(2) When only one stack of shortwood is loaded crosswise, it must be secured with at least two tiedowns. The tiedowns must attach to the vehicle frame at the front and rear of the load, and must cross the load in this direction.
(3) When two tiedowns are used, they must be positioned at approximately one-third and two-thirds of the length of the logs.
(4) A vehicle that is more than 10 meters (33 feet) long must be equipped with center stakes, or comparable devices, to divide it into sections approximately equal in length. Where a vehicle is so divided, each tiedown must secure the highest log on each side of the center stake, and must be fastened below these logs. It may be fixed at each end and tensioned from the middle, or fixed in the middle and tensioned from each end, or it may pass through a pulley or equivalent device in the middle and be tensioned from one end.
(5) Any structure or stake that is subjected to an upward force when the tiedowns are tensioned must be anchored to resist that force.
(6) If two stacks of shortwood are loaded side-by-side, in addition to meeting the requirements of paragraphs (d)(1) through (d)(5) of this section, they must be loaded so that:
(i) There is no space between the two stacks of logs;
(ii) The outside of each stack is raised at least 2.5 cm (1 in) within 10 cm (4 in) of the end of the logs or the side of the vehicle;
(iii) The highest log is no more than 2.44 m (8 ft) above the deck; and
(iv) At least one tiedown is used lengthwise across each stack of logs.
(e) Securement of logs loaded lengthwise on flatbed and frame vehicles - (1) Shortwood. In addition to meeting the requirements of paragraphs (b) and (c) of this section, each stack of shortwood loaded lengthwise on a frame vehicle or on a flatbed must be cradled in a bunk unit or contained by stakes and
(i) Secured to the vehicle by at least two tiedowns, or
(ii) If all the logs in any stack are blocked in the front by a front-end structure strong enough to restrain the load, or by another stack of logs, and blocked in the rear by another stack of logs or vehicle end structure, the stack may be secured with one tiedown. If one tiedown is used, it must be positioned about midway between the stakes, or
(iii) Be bound by at least two tiedown-type devices such as wire rope, used as wrappers that encircle the entire load at locations along the load that provide effective securement. If wrappers are being used to bundle the logs together, the wrappers are not required to be attached to the vehicle.
(2) Longwood. Longwood must be cradled in two or more bunks and must either:
(i) Be secured to the vehicle by at least two tiedowns at locations that provide effective securement, or
(ii) Be bound by at least two tiedown-type devices, such as wire rope, used as wrappers that encircle the entire load at locations along the load that provide effective securement. If a wrapper(s) is being used to bundle the logs together, the wrapper is not required to be attached to the vehicle.
(f) Securement of logs transported on pole trailers. (1) The load must be secured by at least one tiedown at each bunk, or alternatively, by at least two tiedowns used as wrappers that encircle the entire load at locations along the load that provide effective securement.
(2) The front and rear wrappers must be at least 3.04 meters (10 feet) apart.
(3) Large diameter single and double log loads must be immobilized with chock blocks or other equivalent means to prevent shifting.
(4) Large diameter logs that rise above bunks must be secured to the underlying load with at least two additional wrappers.