40 CFR 419.42 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available (BPT).

View all text of Subpart D [§ 419.40 - § 419.47]

§ 419.42 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available (BPT).

(a) Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available (BPT):

Pollutant or pollutant property	BPT effluent limitations		Maximum for any 1 day	Average of daily values for 30 consecutive days shall not exceed		Metric units (kilograms per 1,000 m 3 of feedstock)		BOD 5	50.6	25.8	TSS	35.6	22.7	COD 1	360.0	187.0	Oil and grease	16.2	8.5	Phenolic compounds	0.38	0.184	Ammonia as N	23.4	10.6	Sulfide	0.33	0.150	Total chromium	0.77	0.45	Hexavalent chromium	0.068	0.030	pH	( 2)	( 2)		English units (pounds per 1,000 bbl of feedstock)		BOD5	17.9	9.1	TSS	12.5	8.0	COD 1	127.0	66.0	Oil and grease	5.7	3.0	Phenolic compounds	0.133	0.065	Ammonia as N	8.3	3.8	Sulfide	0.118	0.053	Total chromium	0.273	0.160	Hexavalent chromium	0.024	0.011	pH	( 2)	( 2)

1 See footnote following table in § 419.13(d).

2 Within the range of 6.0 to 9.0.

(b) The limits set forth in paragraph (a) of this section are to be multiplied by the following factors to calculate the maximum for any one day and maximum average of daily values for thirty consecutive days.

(1) Size factor.

1,000 bbl of feedstock per stream day	Size factor	Less than 49.9	0.71	50.0 to 74.9	0.74	75.0 to 99.9	0.81	100.0 to 124.9	0.88	125.0 to 149.9	0.97	150.0 to 174.9	1.05	175.0 to 199.9	1.14	200.0 or greater	1.19

(2) Process factor.

Process configuration	Process factor	Less than 6.49	0.81	6.5 to 7.49	0.88	7.5 to 7.99	1.00	8.0 to 8.49	1.09	8.5 to 8.99	1.19	9.0 to 9.49	1.29	9.5 to 9.99	1.41	10.0 to 10.49	1.53	10.5 to 10.99	1.67	11.0 to 11.49	1.82	11.5 to 11.99	1.98	12.0 to 12.49	2.15	12.5 to 12.99	2.34	13.0 or greater	2.44

(3) Example of the application of the above factors. Example—Lube refinery 125, 000 bbl per stream day throughput.

Calculation of the Process Configuration

Process category	Process included	Weighting factor	Crude	Atm crude distillation Vacuum, crude distillation Desalting	1	Cracking and coking	Fluid cat. cracking Vis-breaking Thermal cracking Moving bed cat. cracking Hydrocracking Fluid coking Delayed coking	6	Lube	Further defined in the development document	13	Asphalt	Asphalt production Asphalt oxidation Asphalt emulsifying	12

Process	Capacity (1,000 bbl per stream day)	Capacity relative to throughput	Weighting Factor	Processing configuration	Crude:					Atm	125.0	1.0			Vacuum	60.0	0.48			Desalting	125.0	1.0			Total		2.48	× 1	= 2.48	Cracking-FCC	41.0	0.328			Hydrocracking	20.0	0.160			Total		0.488	× 6	= 2.93	Lubes	5.3	0.042				4.0	0.032				4.9	0.039			Total		0.113	× 13	= 1.47	Asphalt	4.0	0.032	× 12	= .38	Refinery process configuration				= 7.26

Notes:

See table § 419.42(b)(2) for process factor. Process factor = 0.88.

See table § 419.42(b)(1) for size factor for 125,000 bbl per stream day lube refinery. Size factor = 0.97.

To calculate the limits for each parameter, multiply the limit § 419.42(a) by both the process factor and size factor. BOD5 limit (maximum for any 1 day) = 17.9 × 0.88 × 0.97 = 15.3 lb. per 1,000 bbl of feedstock.

(c) The provisions of § 419.12(c) apply to discharges of process wastewater pollutants attributable to ballast water by a point source subject to the provisions of this subpart.

(d) The quantity and quality of pollutants or pollutant properties controlled by this paragraph, attributable to once-through cooling water, are excluded from the discharge allowed by paragraph (b) of this section. Once-through cooling water may be discharged with a total organic carbon concentration not to exceed 5 mg/l.

(e) Effluent limitations for contaminated runoff. The following effluent limitations constitute the quantity and quality of pollutants or pollutant properties controlled by this paragraph and attributable to contaminated runoff, which may be discharged after the application of the best practicable control technology currently available by a point source subject to this subpart.

(1) If wastewater consists solely of contaminated runoff and is not commingled or treated with process wastewater, it may be discharged if it does not exceed 15 mg/l oil and grease and 110 mg/l total organic carbon (TOC) based upon an analysis of any single grab or composite sample.

(2) If contaminated runoff is commingled or treated with process wastewater, or if wastewater consisting solely of contaminated runoff which exceeds 15 mg/l oil and grease or 110 mg/l TOC is not commingled or treated with any other type of wastewater, the quantity of pollutants discharged shall not exceed the quantity determined by multiplying the flow of contaminated runoff as determined by the permit writer times the concentrations listed in the following table:

Pollutant or pollutant property	BPT effluent limitations for contaminated runoff		Maximum for any 1 day	Average of daily values for 30 consecutive days shall not exceed		Metric units (kilograms per 1,000 m 3 of flow)		BOD5	48.	26.	TSS	33.	21.	COD 1	360.	180.	Oil and grease	15.	8.	Phenolic compounds (4AAP)	0.35	0.17	Total chromium	0.73	0.43	Hexavalent chromium	0.062	0.028	pH	( 2)	( 2)		English units (pounds per 1,000 gallons of flow)		BOD5	0.40	0.22	TSS	0.28	0.18	COD 1	3.0	1.5	Oil and grease	0.13	0.067	Phenolic compounds (4AAP)	0.0029	0.0014	Total chromium	0.0060	0.0035	Hexavalent chromium	0.00052	0.00023	pH	( 2)	( 2)

1 In any case in which the applicant can demonstrate that the chloride ion concentration in the effluent exceeds 1,000 mg/l (1,000 ppm), the permitting authority may substitute TOC as a parameter in lieu of COD. A TOC effluent limitation shall be based on effluent data from the particular refinery which correlates TOC to BOD5. If in the judgment of the permitting authority, adequate correlation data are not available, the effluent limitations for TOC shall be established at a ratio of 2.2 to 1 to the applicable effluent limitations for BOD5.

2 Within the range of 6.0 to 9.0.

[47 FR 46446, Oct. 18, 1982, as amended at 50 FR 28522, 28523, July 12, 1985; 50 FR 32414, Aug. 12, 1985]